New Design Parallel Shaft Cylindrical Gear Reductions

  1. Application

The reducer is mainly used in lifting, mining, general chemical, textile, light industry and other industries. Its applicable conditions are as follows:

  1. Reducer gear transmission circular speed is not more than 10 meters/second;
  2. The speed of the high speed shaft of the reducer shall not be greater than 1500 revolutions/min;
  3. Parallel Shaft Cylindrical Gear Reducers is used for positive and negative operation;
  4. Deceleration machine working environment temperature of 40 ℃ to + 40 ℃;
  5. Reducer has nine transmission ratios, nine configuration types and three types of low speed shaft shaft end;
  6. The transmission ratio of such reducer is: 48.57, 40.17, 31.5, 23.34, 20.49, 15.75, 12.64, 10.35, 8.23.

 

  1. All Type

Parallel Shaft Cylindrical Gear Reducers has two stages of transmission, there are nine types of assembly, the input shaft extension is conical, the output shaft end by cylindrical (Z), gear (CA, C) a level of euclipd (cross slider) coupling (F).

Parallel Shaft Cylindrical Gear Speed Reducers
Parallel Shaft Cylindrical Gear Speed Reducers

 

  1. Difference

Parallel Shaft Cylindrical Gear Reducers is involute cylindrical gear reducer, ZQ (H) type is cylindrical gear reducer, which is formed on the basis of ZQ type involute cylindrical gear reducer series. Time has proved that compared with involute gear of the same specification, circular arc gear not only has a longer service life, but also has a larger capacity, higher strength and less wear on the tooth surface.

 

These two kinds of Parallel Shaft Cylindrical Gear Reducers are mainly used for lifting machinery, also can be used in mining machinery, chemical industry, light industry and other general equipment. The adaptive conditions are: the high-speed shaft speed is not greater than 1500r/min; Operating environment temperature is -40 to +45 degrees. Suitable for positive and negative operation.

Parallel Shaft Cylindrical Gear Speed Reducers
Parallel Shaft Cylindrical Gear Speed Reducers

 

  1. Installation and Use

The Parallel Shaft Cylindrical Gear Reducers is lubricated by the closed transmission oil pool. The oil level of the lubricating oil is indicated by the circular oil mark on the base of the machine. When the reducer stops running, the oil level is within the range indicated by the oil mark.

If you need to open the boot cover maintenance, you should pay attention to whether the cover is covered with sealant, if there is sealant, the screw hole on the machine cover can be opened with screws, do not hammer the sealing surface, inspection must be done to check whether the sealing surface and the through cover are not damaged, sealant residue is not clean, whether it will cause oil leakage.

 

  1. Maintain

Parallel Shaft Cylindrical Gear Reducers should pay special attention to the early work of oil cleaning, if the oil is dirty (especially metal foam mixed), should immediately change the oil, in the oil at the same time, should remove the dirt inside the body. The quality of oil must be checked regularly (not less than once every six months).

The state of meshing working surface should be checked regularly, especially in the early stage of work when the tooth surface abrasion phenomenon, such as abrasion area is not more than 20% of the tooth working surface (along the tooth length and tooth height), allowing a little dressing with a whetstone or scraper.

 

 

Christine Zhu ( Sales Department; Miss. )          

NER GROUP CO.,LIMITED                            
Tel:+86-535-6330966
Mobile:+86-13688909643
http://www.bonwaygroup.com/
https://twitter.com/gearboxmotor
https://www.facebook.com/sogears1993
Viber/Line/Whatsapp/Wechat: 008613688909643
Email: This email address is being protected from spambots. You need JavaScript enabled to view it.;  

Skype ID: This email address is being protected from spambots. You need JavaScript enabled to view it.
Factory Add: No.5 Wanshoushan Road, Yantai, Shandong Province, China (264006)